体积表面电阻率测试仪器

体积表面电阻率测试仪器主要特点

 u    电阻测量范围 1×104Ω ～1×1018 Ω；

u    电流测量范围 2×10-4Ａ ～1×10-16Ａ；

u    体积小、重量轻、准确度高；

u   *的被测电阻、和流过电阻的电流双显示，使操作测量更加方便；

u   性能稳定、读数方便；

u   既能测电阻又能测电流；

u   测试电压有六种选择DC10V、50V、100V、250V、500V、1000V；

u   使用操作简便，在任何电阻量程和测试电压下均直接读显示数字结果，免去要乘以一个系数的麻烦，使测量超高电阻就如用万用表测量普通电阻样简便。

体积表面电阻率测试仪器使用条件

①环境温度： 0～40℃

②相对温度：≤70%

③供电电流：交流 220V±10%50Hz

2.3 仪器可连续工作 8 小时

2.4 消耗功率：约 10W

2.5 外形尺寸：长宽深 355mm×320mm×145mm

2.6 重量：约 6kg(主机)

主要标准：

GB/T 1410-2006 固体绝缘材料 体积电阻率和表面电阻率试验方法

GB1672-8液体增塑剂体积电阻率的测定

GB 12014 防静电工作服

GB/T 20991-2007 个体防护装备 鞋的测试方法

GB 4385-1995 防静电鞋、导电鞋技术要求

GB 12158-2006 防止静电事故通用导则

GB 4655-2003 橡胶工业静电安全规程

GB/T  1692-2008 硫化橡胶绝缘电阻的测定

GB/T 12703.6-2010 纺织品 静电性能的评定 第6部分 纤维泄漏电阻

GB 13348-2009 液体石油产品静电安全规程

GB/T 15738-2008 导电和抗静电纤维增强塑料电阻率试验方法

GB/T 18044-2008 地毯 静电习性评价法 行走试验

GB/T 18864-2002 硫化橡胶 工业用抗静电和导电产品 电阻极限范围

GB/T 22042-2008 服装 防静电性能 表面电阻率试验方法

GB/T 22043-2008 服装 防静电性能 通过材料的电阻(垂直电阻)试验方法

GB/T 24249-2009 防静电洁净织物

GB 26539-2011 防静电陶瓷砖 Antistatic ceramic tile

GB/T 26825-2011 抗静电防腐胶

GB 50515-2010 导(防)静电地面设计规范

GB 50611-2010 电子工程防静电设计规范

GJB 105-1998-Z 电子产品防静电放电控制手册

GJB 3007A-2009 防静电工作区技术要求

GJB 5104-2004 无线电引信风帽用防静电涂料及风帽静电性能通用要求

安全注意事项

4.1 使用前务必详阅此说明书，并遵照指示步骤，依次操作。

4.2 请勿使用非原厂提供之附件，以免发生危险。

4.3 进行测试时，本仪器测量端高压输出端上有直流高压输出，严禁人体接触 ，以免触电。

4.4 为避免测试棒本身绝缘泄漏造成误差，接仪器测量端输入的测试棒应尽可 能悬空，不与外界物体相碰。

4.5 当被测物绝缘电阻值高，且测量出现指针不稳现象时，可将仪器测量线屏 蔽端夹子接上。 例如：对电缆测缆芯与缆壳的绝缘时，除将被测物两 端分 别接于输入端与高压 端，再将电缆壳 ，芯之间的内层绝缘物接仪器 “G”，以消 除因 表面漏电而 引起的测量误差。也可用加屏蔽盒的方法， 即将被测物置于金属屏蔽盒内，接上测量线。

Volume surface resistivity tester main characteristics 
 
U resistance measurement range 1 1 x 1018 x 104 Ω ~ Ω; 
 
U current measuring range is 2 x 10-4 a ~ 1 x 10 to 16 a. 
 
U small volume, light weight, high accuracy; 
 
U unique resistance being measured, according to the current through the resistor, and double make the measurement more convenient operation; 
 
U stable performance, easy reading; 
 
U both can measure resistance and can measure current; 
 
U test voltage DC10V of six kinds of choices, 50 v, 100 v, 250 v, 500 v, 1000 v; 
 
U use simple operation, are directly under any resistance range and testing voltage reading display Numbers as a result, the bother of should be multiplied by a coefficient, makes the measuring high resistance as ordinary resistance is measured with a multimeter sample is simple. 
 
 
 
 
 
 
 
Volume surface resistivity tester using conditions 
 
1) ambient temperature: 0 ~ 40 ℃ 
 
(2) the relative humidity: 70% or less 
 
(3) power supply current, ac 220 v + 10% for 50 hz 
 
2.3 the instrument can work continuously for 8 hours 
 
2.4 consumed power: about 10 w 
 
2.5 dimensions: width 355 mm * 320 mm * 320 mm deep 
 
2.6 weight: about 6 kg (host) 
 
 
 
 
 
 
Surface resistivity tester volume main criteria: 
 
 
 
GB/T 1410-2006 of solid insulating materials Volume resistivity and surface resistivity test method 
 
GB1672-8 liquid plasticizer of volume resistivity measurement 
 
GB 12014 anti-static overalls 
 
GB/T 20991-2007 test method of the individual protective equipment of shoes 
 
GB 4385-1995, anti-static shoes, conductive technical requirements 
 
Prevent electrostatic guide general accident of GB 12158-12158 
 
GB 4655-2003 rubber industrial electrostatic safety procedures 
 
GB/T 1692-2008 vulcanized rubber insulation resistance measurement 
 
GB/T 12703.6 2010 textile electrostatic performance evaluation Part 6 fiber leakage resistance 
 
GB 13348-2009 liquid petroleum products electrostatic safety procedures 
 
GB/T 15738-2008, conductive and antistatic fibre reinforced plastics resistivity test method 
 
GB/T 18044-2008 - carpet static walking behavior evaluation test 
 
GB/T 18864-2002 - vulcanized rubber industry with antistatic and conductive products resistance limit range 
 
GB/T 22042-2008 clothing antistatic performance surface resistivity test method 
 
GB/T 22043-2008 clothing antistatic performance by the resistance of the material (vertical resistance) test method 
 
GB/T 24249-2009, anti-static clean fabric 
 
GB 26539-2011 anti-static ceramic tile Antistatic ceramic tile 
 
Anti-static anticorrosion adhesive GB/T 26825-26825 
 
GB 50515-50515 lead (prevention) electrostatic surface design specification 
 
GB 50611-50611 electronic engineering antistatic design specifications 
 
GJB 105-1998 - Z electronic products electrostatic discharge manual control 
 
GJB 3007 a - 2009 anti-static work area technical requirements 
 
GJB 5104-2004 radio fuze cap with antistatic coatings and cowl electrostatic general performance requirements 
 
 
 
 
 
 
Volume and surface resistivity tester security considerations 
 
4.1 be sure to read the manual before use and follow the instructions step, operating in turn. 
 
4.2 do not use the original factory to provide the attachment, thank you for your cooperation. 
 
4.3 during the test, the instrument measuring the dc high voltage output high voltage output, it is strictly prohibited to human exposure, so as to avoid electric shock. 
 
4.4 to avoid test bar insulation leakage error caused by itself, by instrument measuring the input can be hung up test bar, no object collision with the outside world. 
 
Analyte 4.5 when a high insulation resistance, and measure the instability phenomenon appear Pointers, line screen can be measured All the clip connected. For example: the insulation of the cable and cable to cable measured shell, in addition to the analyte to the two end points Don't pick up the input and the high pressure side, and then to a shell, the cable core between inner insulation instruments "G", to eliminate the error of measurement caused by surface leakage. Method can also be used with shielding box, is about to be tested on the metal shielding box, measuring line.